Melling High Performance Oil Pump
Level III Performance Oil Pumps 25% additional Volume with enhanced featuers over stock replacement pumps. Don't Live in the Past, Step into the Present with the NEW Melling High-Performance Oil Pump with C&C Housing and Cover. This Pump Contains Pressure Balanced (anti-cavitation) Grooves in the Body and Cover and are to Prevent Cavitation at the High RPM's Seen in High-Performance Engines
The drive and idler shafts have been extended to allow for additional support in the cover. Supporting the shafts in both the housing and cover eliminates dynamic shaft deflection at increased RPM levels. The cover is dowelled to the pump housing to assure alignment of the shaft bores. The gears are steel billet. The relief valve has a screw-in plug instead of a pin. The pickup screen hole is machined for press fit screen. The housing and cover are CNC machined and manganese phosphate coated for wear and rust prevention. An additional spring, the original stock replacement, is supplied which will reduce bypass pressure if needed. The same as the 10778 except with the addition of anti-cavitation grooves machined in the housing and cover. The grooves reduce cavitation effects in high RPM applications. Idle pressure slightly reduced. Designed for Racing and High-Performance Applications and every Teague Custom Marine Engine only.
25% higher volume over stock. The idler shaft have been extended to allow for additional support in the cover. Supporting the shaft in both the housing and cover eliminates dynamic shaft deflection at increased RPM levels. The cover is doweled to the pump housing to assure alignment of the shaft bores. The relief valve has a screw-in plug instead of a pin. The drive shaft has a male hex drive with the corresponding female hex intermediate shaft supplied. The pickup screen hole is ¾" and machined for OE press fit screen. The housing and cover are CNC machined and manganese phosphate coated for wear and rust prevention. An additional spring, the original stock replacement, is supplied which will reduce bypass pressure if needed. This Pump is a High Performance Pump. If a Lower Pressure is Desired, Remove the Colored High Pressure Spring and Replace it with Enclosed Non Colored Spring.
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
Marine Oil Pumps
Level III Performance Oil Pumps 25% additional Volume with enhanced featuers over stock replacement pumps. Don't Live in the Past, Step into the Present with the NEW Melling High-Performance Oil Pump with C&C Housing and Cover. This Pump Contains Pressure Balanced (anti-cavitation) Grooves in the Body and Cover and are to Prevent Cavitation at the High RPM's Seen in High-Performance Engines
The drive and idler shafts have been extended to allow for additional support in the cover. Supporting the shafts in both the housing and cover eliminates dynamic shaft deflection at increased RPM levels. The cover is dowelled to the pump housing to assure alignment of the shaft bores. The gears are steel billet. The relief valve has a screw-in plug instead of a pin. The pickup screen hole is machined for press fit screen. The housing and cover are CNC machined and manganese phosphate coated for wear and rust prevention. An additional spring, the original stock replacement, is supplied which will reduce bypass pressure if needed. The same as the 10778 except with the addition of anti-cavitation grooves machined in the housing and cover. The grooves reduce cavitation effects in high RPM applications. Idle pressure slightly reduced. Designed for Racing and High-Performance Applications and every Teague Custom Marine Engine only.
25% higher volume over stock. The idler shaft have been extended to allow for additional support in the cover. Supporting the shaft in both the housing and cover eliminates dynamic shaft deflection at increased RPM levels. The cover is doweled to the pump housing to assure alignment of the shaft bores. The relief valve has a screw-in plug instead of a pin. The drive shaft has a male hex drive with the corresponding female hex intermediate shaft supplied. The pickup screen hole is ¾" and machined for OE press fit screen. The housing and cover are CNC machined and manganese phosphate coated for wear and rust prevention. An additional spring, the original stock replacement, is supplied which will reduce bypass pressure if needed. This Pump is a High Performance Pump. If a Lower Pressure is Desired, Remove the Colored High Pressure Spring and Replace it with Enclosed Non Colored Spring.
| Model | MEL 0-10778 |
|---|---|
| SKU | MEL 0-10778 |
| Manufacturer | MELLING |